Metapace S-62 Manual Página 67
- Página / 205
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
59
Update
Chapter 2
Selecting Output Interface
2.3.3 ACK/NAK TIMEOUT
By default, the scanner sends data to the host without waiting for an ACK/NAK response
before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If
no response within the specified period of time, the scanner will attempt to send the
same data three more times. If all the attempts fail without any notification, data loss
will occur.
1) Read the label above to specify the time interval for the scanner to send data and
wait for a response from the host.
2) Read the “
Decimal Value” label on page 192. For example, read “1” and “0” for the
scanner to automatically shut down after being idle for 1 second.
3) Read the “Validate” label on the same page to complete this setting.
ACK/NAK Error Beep
Note: We suggest enabling the error beep so that you will be notified of such data loss
and have the scanner re-read data.
2.3.4 SWITCH BETWEEN MASTER/SLAVE MODE
After the scanner has established a connection as a SPP slave device, you may have it
read the “Activate BT SPP, Master Mode” setup label to switch to SPP Master Mode. This
will result in easy and reliable re-connection, just like connecting with the cradle.
ACK/NAK Time
-
O
ut after …
(
*0 ~ 99)
Enable Error Beep
*
Disable Error Beep
- IMPORTANT NOTICES 3
- CONTENTS 4
- INTRODUCTION 9
- INSTALLING THE BATTERY 10
- SETTING UP THE CRADLE 11
- SYMBOLOGIES SUPPORTED 15
- QUICK START 16
- Quick Start 17
- ENTER CONFIGURATION MODE 18
- EXIT CONFIGURATION MODE 18
- Refer to Appendix III 23
- LIST THE CURRENT SETTINGS 24
- Chapter 1 26
- 1.2 MEMORY 29
- 1.2.1 TRANSMIT BUFFER 29
- 1.2.2 MEMORY MODE 30
- Send Data 31
- Clear Data & Confirm 31
- Metapace S-2 Hardware 32
- 1.3.1 GOOD READ LED 33
- 1.3.2 GOOD READ LED DURATION 33
- Beeping 34
- Meaning 34
- 1.4.1 BEEPER VOLUME 35
- 1.4.2 GOOD READ BEEP 36
- 1.4.3 LOW BATTERY ALARM 37
- 1.5 SEND “NR” TO HOST 38
- 1.6 SCAN MODES 39
- 1.6.1 CONTINUOUS MODE 40
- 1.6.5 AUTO POWER OFF MODE 42
- 1.6.6 AIMING MODE 42
- 1.6.7 MULTI-BARCODE MODE 43
- 1.6.8 ALTERNATE MODE 43
- 1.8 DELAY BETWEEN RE-READ 45
- Continuous mode 45
- Auto Power Off mode 45
- Alternate mode 45
- 1.11 AUTO-SENSE MODE 48
- 1.13 NEGATIVE BARCODES 49
- 1.14 EFFECTIVE DECODING AREA 50
- 1.14.1 POSITIONING WINDOW 50
- 1.14.2 ADJUSTING WINDOW 50
- Percentage for Right Half 51
- Chapter 2 52
- 2.1 BT HID 53
- 2.1.2 RESET CONNECTION 54
- Cap Lock Type Description 57
- Alphabets Transmission 58
- 2.1.4 INTER-FUNCTION DELAY 61
- 2.2 BT SPP SLAVE 62
- 2.2.2 INTER-FUNCTION DELAY 62
- 2.2.3 ACK/NAK TIMEOUT 63
- 2.3 BT SPP MASTER 64
- “Set Connection” label 64
- “MAC ID” label 64
- 2.3.2 INTER-FUNCTION DELAY 66
- 2.3.3 ACK/NAK TIMEOUT 67
- 2.4.2 KEYBOARD SETTINGS 69
- Digits Transmission 74
- ALT Composing 74
- Laptop Support 74
- 2.4.3 INTER-CHARACTER DELAY 75
- 2.4.4 INTER-FUNCTION DELAY 75
- 2.5 RS-232 VIA THE CRADLE 76
- 2.5.2 BAUD RATE 76
- 2.5.3 DATA BITS 77
- 2.5.4 PARITY 77
- 2.5.5 STOP BIT 78
- 2.5.6 FLOW CONTROL 78
- 2.5.7 INTER-CHARACTER DELAY 79
- 2.5.8 INTER-FUNCTION DELAY 79
- 2.5.9 ACK/NAK TIMEOUT 80
- 2.6 USB HID VIA THE CRADLE 81
- 2.6.3 INTER-FUNCTION DELAY 89
- 2.7.2 INTER-FUNCTION DELAY 90
- 2.7.3 ACK/NAK TIMEOUT 91
- Chapter 3 92
- 3.1.2 CHANGE INTERFACE 94
- Sniff Mode (Power-saving) 95
- 3.2 CONNECTING VIA BLUETOOTH 96
- DONGLE 96
- 3.2.1 CHANGE INTERFACE 96
- Device Name Broadcasting 97
- Entering preset PIN code… 99
- 3.2.3 CONNECT TO DONGLE 100
- 10. Click [Finish] 104
- Notepad.exe if using BT HID 106
- Chapter 4 107
- 4.1 CODABAR 108
- 4.1.3 CLSI CONVERSION 109
- 4.2 CODE 25 – INDUSTRIAL 25 110
- 4.2.2 VERIFY CHECK DIGIT 111
- 4.2.3 TRANSMIT CHECK DIGIT 111
- 4.3 CODE 25 – INTERLEAVED 25 113
- 4.3.2 VERIFY CHECK DIGIT 114
- 4.3.3 TRANSMIT CHECK DIGIT 114
- 4.4 CODE 25 – MATRIX 25 116
- 4.4.2 VERIFY CHECK DIGIT 117
- 4.4.3 TRANSMIT CHECK DIGIT 117
- 4.5 CODE 39 119
- 4.5.2 VERIFY CHECK DIGIT 119
- 4.5.3 TRANSMIT CHECK DIGIT 120
- 4.6 CODE 93 121
- 4.7 CODE 128 121
- 4.8 EAN-8 122
- 4.8.1 CONVERT TO EAN-13 123
- 4.8.2 TRANSMIT CHECK DIGIT 123
- 4.9 EAN-13 124
- 4.9.1 ISBN CONVERSION 125
- 4.9.2 ISSN CONVERSION 125
- 4.9.3 TRANSMIT CHECK DIGIT 125
- 4.9.4 SECURITY LEVEL 126
- 4.10 GS1-128 (EAN-128) 127
- 4.10.1 CODE ID TRANSMISSION 127
- 4.11 ISBT 128 128
- 4.12 MSI 129
- 4.12.1 VERIFY CHECK DIGIT 129
- 4.12.2 TRANSMIT CHECK DIGIT 130
- 4.13 FRENCH PHARMACODE 132
- 4.13.1 TRANSMIT CHECK DIGIT 132
- 4.14 ITALIAN PHARMACODE 133
- 4.14.1 TRANSMIT CHECK DIGIT 133
- 4.15 PLESSEY 134
- 4.15.1 CONVERT TO UK PLESSEY 134
- 4.15.2 TRANSMIT CHECK DIGIT 134
- 4.16.1 CODE ID SELECTION 135
- Application ID Transmission 138
- Transmit Check Digit 138
- 4.17 TELEPEN 139
- 4.18 UPC-A 140
- 4.18.1 CONVERT TO EAN-13 141
- 4.18.3 TRANSMIT CHECK DIGIT 141
- 4.19 UPC-E 142
- 4.19.4 TRANSMIT CHECK DIGIT 144
- Chapter 5 145
- Enter Setup 146
- Metapace S-2 Hardware Manual 146
- 5.4.2 CHANGE CODE ID 155
- 5.4.3 CLEAR CODE ID SETTINGS 157
- 5.5 LENGTH CODE 158
- 5.6 MULTI-BARCODE EDITOR 161
- Code Type 161
- Edit Output Sequence 162
- Remove Special Character 164
- Chapter 6 165
- 6.1.2 EXCLUSIVE DATA EDITING 167
- End Programming Format 168
- 6.2.2 RESTORE DEFAULT FORMAT 170
- 6.3.1 APPLICABLE CODE TYPE 171
- 6.3.2 DATA LENGTH 175
- 6.4.3 TOTAL NUMBER OF FIELDS 178
- 6.4.4 FIELD SETTINGS 179
- Field 2 Setting 180
- 173 181
- Field 3 Setting 181
- Field 4 Setting 182
- 175 183
- Field 5 Setting 183
- Additional Fields 184
- Key Type Key Status 184
- 6.6 PROGRAMMING EXAMPLES 187
- 6.6.1 EXAMPLE I 187
- SPECIFICATIONS 189
- Appendix I 191
- CRADLE SERIAL COMMANDS 193
- 187 195
- Version<CR> 195
- GetID<CR> 195
- Download<CR> 195
- LoadBridge<CR> 195
- EXAMPLE 196
- Appendix II 197
- KEY TYPE & STATUS 198
- KEY TYPE 198
- KEY STATUS 198
- Appendix III 200
- HEXADECIMAL SYSTEM 201
- ASCII TABLE 202
- USE PRESET PIN 203
- 197 205
- Reject Random PIN Request 205
Manuais e produtos relacionados com Leitores de códigos de barras Metapace S-62
(20 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais